Sun Mechanical Contracting, Inc. Jobs Hiring Now

Performs service and maintenance on commercial-grade HVAC systems.

Essential Duties and Responsibilities include the following (other duties may be assigned):

• Obtain and maintain required certifications.
• Comply with all applicable standards, policies, and procedures, including safety procedures and the maintenance of a clean work area.
• Repair or replace defective equipment, components, or wiring.
• Test electrical circuits or components for continuity, using electrical test equipment.
• Reassemble and test equipment following repairs.
• Inspect and test systems to verify system compliance with plans and specifications or to detect and locate malfunctions.
• Discuss heating-cooling system malfunctions with users to isolate problems or to verify that malfunctions have been corrected.
• Record and report all faults, deficiencies, and other unusual occurrences, as well as the time and materials expended on work orders.
• Test pipe or tubing joints or connections for leaks, using pressure gauge or soap-and-water solution.
• Adjust system controls to setting recommended by manufacturer to balance system, using hand tools.
• Recommend, develop, or perform preventive or general maintenance procedures, such as cleaning, power-washing, vacuuming equipment, oiling parts or changing filters.
• Lay out and connect electrical wiring between controls and equipment, according to wiring diagrams, using electrician's hand tools.
• Install auxiliary components to heating-cooling equipment, such as expansion and discharge valves, air ducts, pipes, blowers, dampers, flues and stokers, following blueprints.
• Assist with other work in coordination with repair and maintenance teams.
• Install, connect and adjust thermostats, humidistats and timers, using hand tools.
• Generate work orders that address deficiencies in need of correction.
• Join pipes or tubing to equipment and to fuel, water or refrigerant source, to form complete circuit.
• Assemble, position and mount heating or cooling equipment, following blueprints.
• Study blueprints, design specifications and manufacturers' recommendations to ascertain the configuration of heating or cooling equipment components and to ensure the proper installation of components.
• Cut or drill holes in floors, walls or roofs to install equipment, using power saws or drills.
• Wrap pipes in insulation, securing it in place with cement or wire bands.
• Measure, cut, thread, or bend pipe or tubing, using pipe fitter's tools.
• Fabricate, assemble, or install duct work or chassis parts, using portable metal-working tools or welding equipment.

Supervisory Responsibilities: No

Competencies

To perform the job successfully, an individual should demonstrate the following competencies:

• Analytical - Designs workflows and procedures.
• Design - Generates creative solutions; Applies design principles; Demonstrates attention to detail.
• Problem Solving - Identifies and resolves problems in a timely manner.
• Technical Skills - Strives to continuously build knowledge and skills; Shares expertise with others.
• Written Communication - Able to read and interpret written information.
• Quality Management - Looks for ways to improve and promote quality; Demonstrates accuracy and thoroughness.
• Planning/Organizing - Prioritizes and plans work activities; Uses time efficiently; Plans for additional resources.
• Quality - Demonstrates accuracy and thoroughness; Looks for ways to improve and promote quality; Monitors own work to ensure quality.
• Safety and Security - Reports potentially unsafe conditions; Uses equipment and materials properly.
• Attendance/Punctuality - Is consistently at work and on time.

Qualifications

To perform this job successfully, an individual must be able to perform each essential duty satisfactorily. The requirements listed below are representative of the knowledge, skill and/or ability required. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.

Education and/or Experience

High school diploma or general education degree (GED); One to two years prior HVAC technician experience or an equivalent combination of education and experience.

Language Skills

Ability to read and interpret documents such as safety rules, operating and maintenance instructions, and procedure manuals. Ability to write routine reports and correspondence. Ability to speak effectively before groups of customers or employees of organization.

Mathematical Skills

Ability to work with basic mathematical concepts such as addition, subtraction, multiplication and division. Ability to apply concepts such as fractions, percentages, ratios and proportions to practical situations.

Reasoning Ability

Ability to apply common sense understanding to carry out instructions furnished in written, oral or diagram form. Ability to deal with problems involving several concrete variables in standardized situations.

Certificates, Licenses, Registrations

Valid Driver’s License

Other Skills and Abilities

Ability to read and interpret blueprints

Physical Demands

The physical demands described here are representative of those that must be met by an employee to successfully perform the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.

While performing the duties of this Job, the employee is regularly required to stand for more than 8 hours per day; walk; use hands to finger, handle or feel; reach with hands and arms above shoulder level; climb or balance; stoop, kneel, crouch or crawl, and talk or hear. The employee must regularly lift and/or carry up to 25 pounds, frequently lift and/or move up to 50 pounds and occasionally lift and/or move up to 100 pounds. Specific vision abilities required by this job include close vision, distance vision, color vision, peripheral vision, depth perception and ability to adjust focus.

Work Environment

The work environment characteristics described here are representative of those an employee encounters while performing the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.

While performing the duties of this job, the employee is regularly exposed to moving mechanical parts and outside weather conditions. The employee is frequently exposed to high, precarious places, fumes or airborne particles and extreme heat. The employee is occasionally exposed to wet and/or humid conditions, toxic or caustic chemicals, extreme cold, risk of electrical shock and vibration. The noise level in the work environment is usually loud.

Sun Mechanical Contracting, Inc. provided the following inclusive hiring information:

We are an equal opportunity employer and considers all qualified applicants equally without regard to race, color, religion, sex, sexual orientation, gender identity, national origin, veteran status, or disability status.

Job Type: Full-time

Pay: $16.00 - $40.00 per hour

Benefits:

• 401(k)
• 401(k) matching
• Dental insurance
• Employee assistance program
• Health insurance
• Life insurance
• Paid time off
• Referral program
• Vision insurance

License/Certification:

• Driver's License (Required)

Ability to Commute:

• Tucson, AZ 85737 (Required)

Ability to Relocate:

• Tucson, AZ 85737: Relocate before starting work (Required)

Work Location: In person